McNETT® - Essentials for Adventure^TM

Repair

• How to Thread A Needle

  • 
  • 

    Step 1:

    Cut the end of the thread at a 45 degree angle. Stiffen the thread with saliva or bees wax. It will be easier to control through the eye than a limp thread. Hold up the needle so the eye of the needle is open toward you. If you are unable to see the eye of the needle, place a contrasting color behind the needle.

  • 

    Step 2:

    Slip the thread into the needle and pull the thread until ends are even. Knot the ends of the thread together (see Knotting The Thread). Straighten the threads and begin sewing. Pull the thread after each stitch to prevent the thread knots.

• Knotting the Thread

  • 
  • 

    Step 1:

    After threading the needle, wrap the ends of thread around the pointer finger. Make an “X” whith the tread.

  • 

    Step 2:

    Place your thumb over the “X”. Roll the thread back and forth a couple of times between you pointer finger and thumb.

  • 

    Step 3:

    Slide the knot off your finger with your thumb, rolling the threads together towards the end of your pointer finger while pinching the thread.

  • 

    Step 4:

    I Slide the knot to the end of the thread by gently sliding the knot to the end of the thread using the end of your pointer finger and thumb.

• Basic Sewing Stitches

  • 
  • 

    Running Stitch

    The running stitch is used to make simple seams in fabrics. It is easily completed by passing your needle in and out of the fabric at equal distances of approximately 1/4”. The stitches on the topside of your fabric should be the same length of the stitches on the underside of your fabric.

  • 

    Backstitch

    The backstitch is one of the strongest types of hand-sewn stitches. The back stitch is used for making small, tight seams that will not leak filling (sleeping bags).

  • 

    Step 1:

    Start out by sewing a couple of stitches over the same spot, and then sew a stitch with a space. Insert the needle from the underside of the fabric layers 1/8” to the left of where your stitching will begin. Pull the thread through to the knot.

  • 

    Step 2:

    Insert the needle 1/8 inch behind where the thread emerges (where your stitching will begin). Bring the needle up 1/4” beyond this insertion, and pull the thread snugly. Bring the needle up 1/4” beyond.

  • 

    Step 3:

    Viewed from the top, backstitching appears as a continuous line of even stitches; viewed underneath, the stitches are twice as long as those on top and they overlap at the ends.

• Replace A Broken Zipper Slider

  • 
  • 

    Step 1:

    Select a slider that matches the one you are removing. The letters that are printed on the slide tell you what size you need. With a seam ripper, carefully remove stitching around lower ends of zipper tapes. Pry off metal stop at bottom of the zipper, careful not to tear the tapes at the base of the zipper teeth

  • 

    Step 2:

    Remove old zipper foot. Take new zipper slider and guide track tapes into the top grooves of the slider, pushing them through to the bottom. Use a pin if needed to work the track tapes through. Pull tapes gently to make sure slider is sitting evenly on tracks. With both tapes threaded through slider, gently pull slider up until locked track teeth appear at bottom.

  • 

    Step 3:

    Sew a new stop at bottom of the tracks with needle and thread. Sew zipper back onto garment where stitching was removed for repair.

• Fix A Broken Tent Pole

  • 
  • 

    Step 1:

    Slide the two broken ends of the tent pole into opposite ends of the pole splint.

  • 

    Step 2:

    Hold pole sleeve firmly in place and wrap duct tape around each end of the pole splint. Make sure tape overlaps the pole and the pole splint

• Re-Coat Tent Floors

  • 
  • 

    Step 1:

    Re-coat worn areas on your tent floor with Tent Sure™ Tent Floor Sealant. Apply to the coated side of the fabric (the inside) using a foam paintbrush. For best results apply Tent Sure in a thin film, using even, sweeping motions to avoid puddles. A single thin coat works best.

• Tent Hole Repairs

  • 
  • 

    Step 1:

    Seam Grip® permanently repairs common pinholes and tears in the tent floor. Apply just enough Seam Grip to cover the hole and spread 1/4” (5mm) beyond. Allow to dry level overnight. For 2 hour cure time, mix Seam Grip with Cotol-240™ before applying.

  • 

    Step 2:

    The Field Repair Kit includes both adhesive and patches. To use the tent immediately, simply cover the pinhole with a Tenacious™ Brand Clean Tape™ peel-and-stick patch.

  • 

    Step 3:

    For larger holes and tears, use a patch as a backing then apply Seam Grip. Remove patch in a few days when the Seam Grip has fully cured.

  • 
  • 

    QUICK FIX - Hot Melt Glue

    Hold Hot Melt Glue stick 2-4 inches above the repair area. Use a match or lighter to melt the glue stick and cover hole or tear with melted glue.

  • 
  • 

    Repairing Mosquito Netting

    Cut the Tenacious Tape to the desired size and shape. Remember to round the corners of your patch. Patches with rounded edges are less likely to come off accidentally. Make tent netting taunt by zipping closed to an assembled tent. Un-zip a small area, just large enough for your hand to go through.

  • 

    Remove backing paper and place patch over repair area. Apply pressure to the patch with fingers. Start at the center of the patch then work out to the edges to avoid bubbles.

  • 

    PERMANENT REPAIR - No-Seeum Netting

    Sew No-Seeum Netting to area around the damaged netting. Sew small stitches 1/4” inside the edge of the No-Seeum netting patch.